HOW TO connect ASHOT With DJI PHANTOM 4 PRO/ADV
MANUAL
AShot set: AShot board, custom flexible flat cable, 3 pin cable, GH5 connector for Reach M+, 2 screws for securing AShot, adhesive tape.
Be extremely careful during installation process of AShot board into your DJI Phantom. Please, read instruction first and make sure that you understand whole process.

AShot manufacturer is not responsible for improper installation.
All actions you perform at your own risk and responsibility
TOOLS
You need: 1.5 mm HEX screwdriver and small crosshead screwdriver and a file.
teardown
Put the drone upside down and unscrew 8 screws using a 1.5 mm hex driver.

Then carefully unscrew 2 cross screws securing flexible cable to gimbal board. Then unplug flexible cable from both DJI's 3-in-1 board and gimbal board.
cable preparation
Unscrew 4 cross screws and unplug gimbal board.

Unplug the flexible cable from rear side of gimbal board and bend down cable's right side 90 degrees as shown in the photo.

Big size photo:
https://ashot.cc/manual/image/IMG_5793.jpg
https://ashot.cc/manual/image/IMG_7615.jpg
cable installation
Connect bended right side of gimbal's flexible cable with small flexible cable came with AShot as shown in the photo.

Big size photo:
https://ashot.cc/manual/image/IMG_0329.jpg
You need to smoothen the sharp edge of the button with a file in order to prevent damage of flexible cable.
assemble gimbal
Plug flexible gimbal cable with attached AShot flexible cable into rear side of gimbal board, then put gimbal board in place and tighten it with 4 cross screws.

Gimbal preparation finished.

Big size photo:
https://ashot.cc/manual/image/IMG_0723.jpg
MOST IMPORTANT PART OF MANUAL
Be even more cautious during this part of installation.
cable preparation
Take DJI's 3-in-1 board's flexible cable in your hand as shown in the photo.
Then attach double-sided tape came with AShot to the back of the connector.

Big size photo:
https://ashot.cc/manual/image/IMG_5389.jpg
https://ashot.cc/manual/image/IMG_5389.jpg
cable bending
Release protective layer from the tape and bend cable 180 degrees so that it sticks to the double-sided tape as shown in the photo.

BE GENTLE!!!
preparation finish
Put reinforcing tape on the cable as shown in the photo.

Install the cable into the gimbal board and tighten 2 cross screws.

ASHOT INSTALLATION
Plug AShot board into DJI's 3-in-1 board and secure it with 2 screws came with AShot to the aluminum radiator.

Big size photo:
https://ashot.cc/manual/image/IMG_1079.jpg
cables connection
Plug BLACK-RED-GREEN cable to 3 pin port on the AShot board (see the photo).
This cable will be connected to Reach M+ board:
BLACK is GROUND;
RED is +5v;
GREEN is for Timemark signal going to GNSS board.

Plug BLUE-YELLOW cable, coming from previously attached custom AShot flexible cable, into 2 pin port as shown in the photo.
assembling
Plug flexible cable, which we earlier attached to gimbal board, into AShot's socket.

Lead BLACK-RED-GREEN cables through the vent holes.
Check all connectors whether they secured properly, then mount gimbal side and tighten with 8 1.5 mm hex screws.

Big size photo:
https://ashot.cc/manual/image/IMG_4043.jpg
reach m+ plugin
Use GH5 connector to connect AShot with Emlid Reach M+ board (GH5 connector included).

Be careful and DO NOT misplace +5v wire with ground wire.
This video is HOW TO ACTIVATE INTERVAL SHOOTING with AShot
Thank you for your interest in our product.